High-quality BLDC brushless motor (outrunner) for model aircraft. Simple front or rear mounting possible. Complete with mounting hardware and small parts.
Features
- Optimised cooling thanks to the open design
- High-quality ball bearings
- Finely balanced rotors
- High-temperature-resistant neodymium magnets
Application
- 3D model aircraft up to 350g
- Aerobatic models up to 400g
- Gliders up to 600g
Scope of delivery
- BOOST 15 Brushless Motor
- Aluminium mounting cross
- 1 propeller adapter each for front and rear bulkhead mounting
- Mounting screws
- Replacement motor shaft
- Instructions German/English
Technical data
Dimensions = 28 x 30mm
Weight = 59g
Shaft Ø = 3.2mm (3.175mm)
LiPo / NiXX = 2 -3 / 6 -10
Revolutions per volt/min. = 1000 rpm (KV)
Max. load (60 s) = 12A
Brushless ESC (recommended) = PICHLER XQ+ 25, #15922
Recommended propeller
PI-CON 8×4, # C5746
PI-CON 9×6, # C5748
Recommended accessories
Brushless ESC PICHLER XQ+ 25, # 15922
Power Watts 150, # C7282
An overview of all BOOST brushless motors can be found here
Note: propellers other than those listed here (e.g. 3-blade or smaller sizes) can of course also be used. The same applies to batteries of a different, for example higher, capacity. Please make sure that the permissible currents (A) are not exceeded. For straightforward current measurement we recommend our proven POWER WATTS 150, # C7282 – an instrument you will need again and again and which should be part of every kit.
Information on our WEEE registration number: we are registered as a producer of electrical and/or electronic equipment with the stiftung elektro-altgeräte register (stiftung ear), Benno-Strauß-Straße 1, 90763 Fürth, Germany, under the following registration number (WEEE reg. no.): DE42729107
High-quality BLDC brushless motor (outrunner) for model aircraft. Simple front or rear mounting possible. Complete with mounting hardware and small parts.
Features
- Optimised cooling thanks to the open design
- High-quality ball bearings
- Finely balanced rotors
- High-temperature-resistant neodymium magnets
Application
- 3D model aircraft up to 350g
- Aerobatic models up to 400g
- Gliders up to 600g
Scope of delivery
- BOOST 15 Brushless Motor
- Aluminium mounting cross
- 1 propeller adapter each for front and rear bulkhead mounting
- Mounting screws
- Replacement motor shaft
- Instructions German/English
Technical data
Dimensions = 28 x 30mm
Weight = 59g
Shaft Ø = 3.2mm (3.175mm)
LiPo / NiXX = 2 -3 / 6 -10
Revolutions per volt/min. = 1000 rpm (KV)
Max. load (60 s) = 12A
Brushless ESC (recommended) = PICHLER XQ+ 25, #15922
Recommended propeller
PI-CON 8×4, # C5746
PI-CON 9×6, # C5748
Recommended accessories
Brushless ESC PICHLER XQ+ 25, # 15922
Power Watts 150, # C7282
An overview of all BOOST brushless motors can be found here
Note: propellers other than those listed here (e.g. 3-blade or smaller sizes) can of course also be used. The same applies to batteries of a different, for example higher, capacity. Please make sure that the permissible currents (A) are not exceeded. For straightforward current measurement we recommend our proven POWER WATTS 150, # C7282 – an instrument you will need again and again and which should be part of every kit.
Information on our WEEE registration number: we are registered as a producer of electrical and/or electronic equipment with the stiftung elektro-altgeräte register (stiftung ear), Benno-Strauß-Straße 1, 90763 Fürth, Germany, under the following registration number (WEEE reg. no.): DE42729107
Rezensionen
Es gibt noch keine Rezensionen.